Wheel Bolts & Nuts — Truck & Trailer

Cold-forged wheel bolts, nuts, U-bolts and clamps for European, American and Japanese trucks.

231 JQ references · grade 10.9 / 12.9 · ten product lines

Request a Quotation

Built with an ALWID audited fastener plant — Nan’an, Quanzhou, Fujian, China

1998Established
20,000 m²Plant area
15,000 m²Workshop floor
231JQ bolt references
10.9 / 12.9Property class
10Product lines
FROM WIRE TO WHEEL

Six operations, one plant, no subcontracting

What a coil of wire goes through before it leaves as a wheel bolt.

01

Cold heading

Wire is cut, headed and extruded on multi-station formers. Head and shank come off the same die set, so the grain follows the part instead of being cut across it.

02

Threading

Threads are formed on automatic tapping machines, then checked with the go/no-go gauge for the size on the drawing.

03

Quenching

A mesh-belt furnace hardens and tempers to property class 10.9 or 12.9, batch by batch, with the hardness logged per lot.

04

Surface

Phosphating, zinc plating or Dacromet. The corrosion hours on the buyer’s drawing decide which, not the price list.

05

Inspection

Torque, salt spray, metallography, material analysis, hardness and impact — six stations, plus a polished section under the microscope.

06

Packing

Neutral cartons or the buyer’s own brand, with size, class and OE number printed on every label.

THE PLANT

Twenty thousand square metres, fifteen of them under roof

Eight workshops in a row. Between operations the part does not leave the site.

Heading and thread-rolling hall — Rongqiao Industrial Area, Nan’an
Heading and thread-rolling hall — Rongqiao Industrial Area, Nan’an
  • 01Cold forging
  • 02Nut boring
  • 03Punching
  • 04Heat treatment — mesh-belt quenching
  • 05Automatic thread tapping
  • 06CNC machining
  • 07Stereoscopic warehouse
  • 08Inspection laboratory

One address for every operation: Rongqiao Industrial Area, Nan’an, Quanzhou.

THE RANGE

Ten lines, one numbering system

JQ numbers run from JQ001 to JQ231 and cover the three bolt series; the other lines carry their own prefix.

Wheel bolts — European JQ

Wheel bolts — European

Mercedes-Benz and Actros, Scania, Volvo, Renault, SAF, BPW, ROR, MAN, Iveco, Trilex

Wheel bolts — American JQ

Wheel bolts — American

Mack, York, Fruehauf, Dodge

Wheel bolts — Japanese JQ

Wheel bolts — Japanese

Isuzu, Mitsubishi Fuso, Hino

Wheel nuts JQC

Wheel nuts

Matched to the bolt series above

Rollers KP

Rollers

Isuzu, Hino, Toyota, Mitsubishi, Mercedes-Benz, BPW, Hyundai

Tie rod ends

Tie rod ends

Mercedes-Benz, Mitsubishi, Hino

Slack adjusters

Slack adjusters

DAF, Volvo, Iveco, Sinotruk, Shacman, Foton, FAW, Dongfeng

Wheel clamps

Wheel clamps

M18 and M20

Castings

Castings

Cast to the buyer’s drawing

Track and blade bolts

Track and blade bolts

14–20 mm, NC and fine thread

WHAT IS CHECKED

Six tests before a carton is closed

The laboratory sits inside the plant, so a failed lot is found before it is packed, not after.

In-house laboratory — hardness, salt spray and metallography
In-house laboratory — hardness, salt spray and metallography
In-house laboratory — hardness, salt spray and metallography

In-house laboratory — hardness, salt spray and metallography

01

Torsion

A bolt is twisted to failure to read the torque the head takes before it shears.

02

Salt spray

Plated and Dacromet parts sit in the chamber for the hours the drawing asks for.

03

Metallography

A polished section shows decarburisation and grain size after quenching.

04

Material analysis

The wire certificate is checked against the melt, not taken on trust.

05

Hardness

Every lot is measured on the head and on the shank — the two must agree.

06

Impact

A drop test on the finished part, at the low temperature the market asks for.

ISO 9001 quality management system — certificate on file
ISO 9001 quality management system — certificate on file
THE SPECIFICATION

What the drawing has to state

Property class10.9 or 12.9
Metric threadM14×1.5 to M22×1.5
Imperial thread7/8″-11 BSF, 7/8″-14 BSF
Across flats19–33 mm
Nut height16–34 mm
FinishPhosphated, zinc-plated or Dacromet
MarkingClass and maker’s mark on the head
WHAT THIS PAGE DOES NOT CLAIM

The limits of what we can show

It lists what the plant’s own catalogue states: the series, the OE numbers, the property classes and the finishes. It does not state unit volumes, customer names or a certificate number, because the documents do not.

Where a buyer needs a figure that is not here, we ask the plant and answer in writing rather than estimate.

BEFORE YOU ASK

Three things that decide the quotation

01

Which axle, which wheel?

One truck can take two bolt lengths. The OE number on the old bolt settles it faster than the model year.

02

Metric or imperial?

European axles are metric; American and some Japanese axles are BSF. Mixing the two is the most common wrong order.

03

How long must it last?

Phosphating is the shortest life and the lowest cost, Dacromet the longest. Salt-spray hours decide, not the finish name.

Quotation is against a list: OE number, thread, length and quantity.

START YOUR PROJECT

Need wheel bolts matched to a list?

Send the OE numbers, the thread and the quantity — we match them to the JQ list and quote with the packing.

market@alwid.cn · www.alwid.cn

English project management · OE-matched references · Export packing included

Reliable aftermarket spare parts solution

ALWID contact QR code

NINGBO HONOR IMPORT AND EXPORT CO.,LTD

Room 223, Building 8, No.1863, Xiangjiang Road, Jiaqiao
Town, Jiading District, Shanghai, China 201803

ISO 9001:2015Quality Management System

© 2026 ALWID. All rights reserved.